Zenith-data-systems MT2000 Manuale Utente Pagina 112
- Pagina / 205
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
5-24
Upgrades and Options
Replacing the Battery
Notice: Observe static precautions. Use an antistatic
wrist strap.
1. Power off the system and remove the side panel as
described earlier in this chapter.
2. Using your finger nail or a small pointed tool, gently
push down the top edge of the battery and pry the
battery out of its socket. Refer to Figure 5-9 for the
socket location.
3. Orient the new battery over its socket so the plus (+)
sign on the battery is facing up.
4. Carefully insert the bottom of the battery into the
socket connectors and gently push the battery into
the socket.
5. Press down on the battery until it is firmly seated in
its socket.
6. Replace the side panel and turn on the system.
7. Run the SCU to restore configuration settings to the
real-time-clock.
- Server MT2000 1
- User’s Guide 1
- Trademarks 2
- PN: 101843-01 6/97 2
- REGULATORY INFORMATION 3
- Safety Notices 4
- Care and Handling 5
- Bill GrahamContents 7
- Bill Graham 10
- Organization 11
- Introduction 12
- Notational Conventions 13
- Features 14
- Overview 15
- Features 17
- Configuration Constraints 17
- System Feature Summary 18
- System Board Features 27
- Processor 31
- Real-Time Clock/Calendar 32
- SCSI Controllers 33
- Peripheral Controller 33
- SCSI Drive Hot-swap Backplane 36
- Removable Media Drive Bays 37
- Power System 38
- Server Security 38
- Hot Swap Power 41
- Hot Swap FAN 42
- Chapter 3 45
- Selecting a Site 46
- Unpacking the System 47
- Making Connections 48
- Connecting the Power Cord 50
- Powering On Your System 51
- Configuring Your System 52
- Billy Graham 53
- Using the SCU 56
- SCU Command Line Parameters 58
- SCU Configuration Settings 59
- ISA Board Configuration 61
- BIOS Setup Utility 64
- Using the BIOS Setup Utility 65
- Using the Utilities Diskette 71
- Viewing the Event Log 73
- SCSISelect Utility 74
- Using the SCSISelect Utility 75
- Exiting SCSISelect 77
- Moving System Board Jumpers 84
- Updating the BIOS 85
- Resetting the CMOS NVRAM 86
- Precautions 89
- Removing a Side Panel 93
- Installing a Side Panel 94
- Removing the Top Cover 95
- Installing the Top Cover 97
- Upgrades and Options 100
- Pentium Pro Processor 100
- Upgrades and Options 101
- Modifying the System Board 107
- Video Memory 108
- Non-Volatile Memory 109
- Real-time Clock Battery 111
- Option Boards 113
- Installation Considerations 114
- Installing an Option Board 118
- Removing an Option Board 121
- Power Supply Module 122
- Swapping Out a Fan Module 139
- Problem Solving 142
- Resetting the System 144
- Troubleshooting Checklists 145
- Problem Solving 146
- Error Checking 149
- Troubleshooting Guide 149
- Power LED Does Not Light 153
- Incorrect Or No Beep Code 156
- BIOS User’s Information 160
- Messages and Beep Codes 163
- System Cabling 170
- Bill GrahamBill Graham 171
- Before You Begin 172
- Static Precautions 172
- RAID Configuration 176
- Memory Configurations 182
- Bill Grahamaerrterterter 183
- Memory DIMM Configurations 184
- Appendix D 188
- Network Operating Systems 190
- Equipment Log 192
- Equipment Log 194
- Glossary 196
- Glossary 198
IBM Zdalne sterowanie podręczniki użytkownika
Zaczynanie od R
Commenti su questo manuale